networking - How configure my beetel adsl2+ 440txi modem as a wireless access point for a pppoe connection

02
2013-08
  • user1075529

    I have a beetel router (adsl2+ 440txi) with wireless settings already configured and connected to laptop. This router is connected to another dsl router which is connected to the internet.

    I tried configuring the beetel router by creating a new pppoe connection with the given username and password (going to 192.168.1.1 and creating a new connection). But it doesn't work; in the connection status for the router, the state is 'not connected' because the 'dsl line is disconnected'. The connection on the laptop says connected to wireless network but no internet access and the pppoe light on the router doesn't blink at all.

    Wondering if i need to make any other configurations. Any help would be appreciated.

    • Answers
  • Spiff

    I believe your Beetel 440txi router has a built-in DSL modem for its WAN port, and doesn't provide an Ethernet WAN port, is that correct?

    If so, then you can't hook its (DSL) WAN port to your other DSL router's (Ethernet) LAN port, because DSL and Ethernet are two different technologies, even though their connectors may look similar in some countries (RJ11 for a telephone/DSL line, wider RJ45 for Ethernet cable).

    Since you already have another DSL router plugged into your DSL-enabled telephone line, let that router be your PPPoE client, NAT gateway, and DHCP server for your home network. If you want to add the Beetel 440txi to the network to provide more Ethernet ports or additional Wi-Fi coverage, then turn off the 440txi's PPPoE, NAT, and DHCP services, and use and Ethernet cable to plug one of the 440txi's Ethernet LAN ports to one of the Ethernet LAN ports on the other DSL router.


    • Related Question

    networking - How to improve my router settings and stop these access attempts to my network
  • D. Veloper

    I have a network at home. ISP modem connects to my router which connects to my computers and laptops. When I look into my router logs I see a load of blocked access attempts. I was wondering if I can stop people from trying to access my wireless network. (My router does not have the ability to power down to decreased its range)

    Please check these logs and my router settings below and I hope you can tell me what I can do to stop this. Also I am wondering if this is the work of one person.

    Also I am wondering if I can improve my router settings, what do you guys think?

    I have a 3Com OfficeConnect router with the latest updates. My router settings:

    • I don't use the default password. (duh)
    • I don't use the regular ip-address but my own.
    • I use a .248 subnet so I can use 5 hosts as the 6th is my router and the first is my network address. Good for my two computers and my two laptops, room for one additional host if needed.
    • I have fixed a few of my DHCP client ip addresses. (is that good?)
    • Gateway's DHCP Server is enabled.
    • My SSID is a latin word I chose and I don't broadcast this name. (although I heard people can still notice my network with specific software as the network is existing)
    • I use WPA encryption with a pre-shared passphrase.
    • I enabled connection control which only allows my laptops MAC addresses to connect to the gateway.
    • When a request from the Internet is not directed to a virtual server it is blocked.
    • Url filter disabled and no pc privileges.
    • Pings from internet are disabled and remote administration is also off.

    Here is are my logs from the past 24 hours, I omitted my own successful logins.

    2009/11/07 23:49:36 : Blocked access attempt from 64.34.14.35
2009/11/08 00:26:43 : Blocked access attempt from 94.231.57.9
2009/11/08 00:49:38 : Blocked access attempt from 209.85.227.105
2009/11/08 00:49:41 : Blocked access attempt from 209.85.229.99
2009/11/08 00:51:25 : Blocked access attempt from 209.85.227.105
2009/11/08 10:54:33 : Blocked access attempt from 94.211.26.19
2009/11/08 11:05:00 : Blocked access attempt from 211.100.229.252
2009/11/08 14:35:08 : Blocked access attempt from 209.85.229.104
2009/11/08 14:36:05 : Blocked access attempt from 209.85.227.105
2009/11/08 14:56:46 : Blocked access attempt from 121.166.196.244

    • Related Answers
  • David Pearce

    It sounds as if you have all bases covered. Regardless of your security settings on your network, you can never stop attempts to access it. It is only when those attempts aren't blocked and are successful you should start considering the security of your network.

    Just one little tid-bit of helpful information…

    I enabled connection control which only allows my laptops MAC addresses to connect to the gateway.

    MAC address filtering (which is what this is) is so incredibly easy to by-pass. These days, faking your MAC address is very trivial and you should never rely solely on MAC filtering.

  • Crash893

    you could try lowering the power of your wifi to more tightly match the physical office space your are servicing. no need to blast it into a public lobby or out onto the street if those are your employees anyway.

    maybe setup a hunnypot ap that goes no where but if anyone connects to it youll know you had a breach of some sort.